How Do You Change The Battery On A Samsung Galaxy S6

Introduction

Use this guide to replace the battery in your Samsung Galaxy S6.

Before disassembling your phone, discharge the battery beneath 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

If your battery is swollen, take appropriate precautions. Practice not oestrus your phone. If needed, yous can use a dropper or syringe to inject isopropyl alcohol (90+%) around the edges of the back cover to weaken the agglutinative. Swollen batteries can be very dangerous, so wear eye protection and practice due circumspection, or have information technology to a professional if you're non certain how to continue.

This guide involves removing the rear drinking glass. Removing the rear drinking glass destroys the agglutinative property it in place. Follow this guide to reinstall the rear glass.

Insert a paper clip or SIM eject tool into the hole in the SIM card slot on the power button side of the phone.

Insert a paper clip or SIM eject tool into the hole in the SIM card slot on the power button side of the phone.
Press to eject the SIM card tray.
Don't printing too difficult or you lot may damage the SIM card tray.

Remove the SIM card tray from the phone.

Remove the SIM carte du jour tray from the phone.

We recommend that you clean your microwave before proceeding, equally any nasty gunk on the bottom may cease upward stuck to the iOpener.
Place the iOpener in the middle of the microwave.
For carousel microwaves: Brand sure the plate spins freely. If your iOpener gets stuck, it may overheat and fire.

Heat the iOpener for xxx seconds.
Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an boosted 30 seconds at a fourth dimension.
Be conscientious non to overheat the iOpener during the repair. Overheating may crusade the iOpener to burst.
Never touch the iOpener if it appears swollen.
If the iOpener is still too hot in the middle to touch, go along using information technology while waiting for it to cool downwardly some more before reheating. A properly heated iOpener should stay warm for up to ten minutes.

Remove the iOpener from the microwave, holding it by i of the two apartment ends to avoid the hot centre.
The iOpener will exist very hot, so be careful when handling it. Apply an oven mitt if necessary.

If you don't have a microwave, follow this pace to oestrus your iOpener in boiling water.
Fill a pot or pan with plenty water to fully submerge an iOpener.
Heat the h2o to a boil. Turn off the estrus.
Place an iOpener into the hot water for 2-iii minutes. Brand sure the iOpener is fully submerged in the water.
Use tongs to extract the heated iOpener from the hot water.
Thoroughly dry the iOpener with a towel.
The iOpener will be very hot, so be careful to hold it but by the stop tabs.
Your iOpener is ready for utilize! If yous need to reheat the iOpener, heat the water to a eddy, plow off the heat, and place the iOpener in the water for 2-3 minutes.

Opening your telephone will compromise its waterproof seals. Accept replacement adhesive prepare before you proceed, or accept care to avert liquid exposure if you reassemble your phone without replacing the adhesive.
If your glass is shattered, put packing record over the entire panel to hold it together during the removal process.
Lay the heated iOpener over the rear panel for nearly ii minutes to loosen the adhesive around the edge of the glass.
Yous may need to reheat and reapply the iOpener several times to get the phone warm plenty. Follow the iOpener instructions to avoid overheating.
Shift the iOpener to estrus the remaining section of the console for another two minutes.
A pilus dryer, rut gun, or hot plate may also exist used, but be careful not to overheat the telephone—the OLED brandish and internal battery are both susceptible to heat damage.

Once the rear glass is hot to the affect, apply a suction cup near the bottom edge of the glass.
Lift on the suction cup to create a small gap underneath the rear glass, and insert an opening choice into the gap.
Optionally, once the choice is inserted, you can add a few drops of isopropyl alcohol into the gap to assist weaken the agglutinative in the following steps.

Slide the selection along the lesser edge of the telephone to slice through the agglutinative securing the rear drinking glass.
Afterwards, it may aid to leave the pick in place and grab a second pick as you keep to the next stride. Leaving the option inserted can help prevent the gum yous just separated from re-adhering.
Re-heat the rear glass every bit needed to prevent the mucilage from cooling and hardening.

Repeat the heating and cut process for the remaining iii sides of the phone.
Get out an opening pick nether each edge to prevent the adhesive from resealing.

Employ an opening choice to piece through whatsoever remaining adhesive.
Remove the rear drinking glass.

To install new rear glass:
Use tweezers to peel away whatsoever remaining adhesive from the phone's chassis.
Clean the adhesion areas with high concentration isopropyl alcohol (at least xc%) and a lint-complimentary cloth. Swipe in one direction simply, non back and forth. This will aid prep the surface for the new agglutinative.
Pare the agglutinative backing off of the new rear glass, carefully line up i edge of the drinking glass confronting the phone chassis, and firmly press the glass onto the phone.
If you lot're reinstalling the erstwhile rear glass, or using rear drinking glass without adhesive pre-installed, follow this guide.

Remove the xiii 3.5mm Phillips #00 screws securing the midframe to the phone.

Earlier you perform this step, make sure y'all've ejected the SIM card tray.
Firmly grasp the border of the midframe assembly.
Lift upwards on the midframe assembly while pushing down on the bombardment to separate the midframe assembly from the rest of the phone.
While lifting the midframe, be careful to avoid snagging it on the audio jack or charging port.
Once the midframe is partially seperated, carefully run an opening pick around the edges of the residue of the phone to split up the top of the midframe.
Exist conscientious not to accidentally insert the opening pick between the glass and display.
To avert damage to the headphone jack, remove the acme of the midframe first, and so push the midframe downward to disengage it from the headphone jack.
You may need to heat and apply an iOpener to the edges of the display to soften the brandish adhesive if midframe separation is hard.

Lift the midframe associates upwardly to separate it from the remainder of the phone.

Utilise the apartment terminate of the spudger to disconnect the battery connector from its socket on the motherboard.

Insert a plastic opening selection between the case and the battery.
Be conscientious to keep the pick as flat as possible to avoid bending the battery, which may damage it and cause it to release dangerous chemicals.
Push the selection further in to separate the battery from the telephone.
If the battery is too strongly adhered for the opening selection, identify a warm iOpener over the battery to loosen the agglutinative.
Alternatively, utilise some isopropyl alcohol under each corner of the battery and let it to penetrate for several minutes to help weaken the adhesive.
Exercise not pry against the motherboard or you may damage the phone.

Remove the battery from the telephone.
Practise not reuse the bombardment after it has been removed, equally doing and so is a potential safe hazard. Supercede it with a new battery.
Follow these instructions to install a new battery and agglutinative.